Understanding

Energy accounting

Measure, compare, act: the foundation of lasting energy savings.

Keeping a building’s energy accounts just as you would keep a company’s books: every meter is read regularly, and every consumption figure is converted, corrected for climate and compared. Energy accounting shows where the energy goes, spots drifts as soon as they appear and proves, with figures to back it up, what each action delivers.

Definition

Accounts in kWh, not in euros.

A bill arrives late, often covers a whole year, mixes estimated instalments, taxes and standing charges, and says nothing about how the energy is used. Energy accounting starts from the meters: it records actual consumption at regular intervals, building by building and, where possible, use by use.

The bill Energy accounting
FrequencyOnce a year, with instalments that are often estimatedAt least once a month; every day, or even every quarter of an hour, with automatic readings
UnitsEuros, including taxes and standing chargeskWh, m³ and litres, then their cost and CO₂ emissions
Level of detailOne total per supply pointBy meter, by building, by use, down to the individual room
ClimateIgnored: a mild winter looks like a savingTaken into account through degree-days
What it is forPayingUnderstanding, comparing, acting and checking

It does not replace the company’s accounts but complements them: set against the bills, the readings let you check them, and the savings measured translate into euros.

Why

You can’t manage what you don’t measure.

Without monitoring, consumption can drift for months without anyone noticing; it is often a year-end adjustment bill that raises the alarm, far too late. Regular monitoring serves six purposes.

Spot drifts

A stuck valve, a badly set schedule, a boiler running at weekends, a water leak: the deviation shows up in the week’s figures, not the year’s.

Know your energy uses

Which buildings, which uses, which rooms consume the most? Priorities are set on measurements, not on impressions.

Measure real savings

After an investment or a new setting, climate-corrected consumption shows what has really been saved.

Check the bills

Meter readings taken on site can be compared with the readings and volumes on the bill: an incorrect estimate shows up immediately.

Negotiate your contracts

An accurate consumption profile is an asset when choosing a tariff, a contracted capacity or a supplier.

Involve the occupants

Simple figures, shared regularly, make efforts visible and help them last.

The method

Six steps, repeated over time.

Energy accounting is not a report you write once: it is a loop. You measure, compare and act, then measure again to check.

  1. Draw up an inventory

    Buildings, heated floor areas, meters (gas, fuel oil, electricity, water, heat, photovoltaic generation), uses and occupancy hours. Each meter is given a name and a clear role.

  2. Read the meters

    On fixed dates, at least once a month. Automatic reading eliminates missed readings and reading errors, and goes down to the day or the hour: that is where drifts become visible.

  3. Convert everything to kWh

    To compare different energy sources, everything is converted to kWh: one litre of fuel oil is worth about 10 kWh, one m³ of natural gas 10 to 11.5 kWh depending on the calorific value shown on the bill. Cost and CO₂ emissions follow from this.

  4. Correct for climate

    A mild winter lowers heating consumption without any effort at all. Degree-days bring every period back to the same reference climate: at last, you compare like with like.

  5. Analyse and compare

    Month on month, year on year, between similar buildings and against benchmark values in kWh/m². Every deviation becomes a lead for action.

  6. Act, then check

    Settings, schedules, controls, building work: every action is dated. The following readings show whether the expected saving is really there, and whether it lasts.

The loop starts again at step 2: each new reading feeds the next analysis.

Degree-days

Comparing two very different winters.

Heating needs depend first and foremost on the outdoor temperature. Degree-days measure how harsh the climate is: each day, you take the difference between a base temperature and the average outdoor temperature, if it is positive, then add up these differences over the month or the year.

The calculation, day by day

Degree-days = base temperature − average outdoor temperature of the day

If the day is warmer than the base, the result is zero: the building needs no heating.

  • Base 16.5 °C, day averaging 4.5 °C: 12 degree-days.
  • Base 16.5 °C, day averaging 18 °C: 0 degree-days.

In Belgium, the 15 °C and 16.5 °C bases are the most widely used. The base is the outdoor temperature above which heating is no longer needed: the sun, the occupants and the appliances then provide enough heat.

Worked example: gas-heated offices

Winter2024-20252025-2026
Gas consumption (kWh)152,000149,000
Degree-days2,1802,410
kWh per degree-day69.761.8
2024-20252025-2026
On the bills
−2%: the effort barely shows.
For the same climate
−11%: the second winter was about 10% colder; normalised to the same climate, the building used 11% less.

For the same climate: consumption normalised to a reference winter of 2,300 degree-days.

Strictly speaking, only the heating share depends on the climate. Domestic hot water, cooking or boiler losses in summer do not: the energy signature makes it possible to separate them.

A B C

Energy signature

An energy portrait of the building.

Plot each month of the year on a graph: degree-days on the horizontal axis, consumption on the vertical axis. The points fall almost on a straight line: this is the building’s energy signature. It tells you three things.

ANon-heating consumption
Where the line crosses the vertical axis: what is consumed with no heating demand at all (hot water, cooking, laundry, production machinery, installation losses). If it is high, there is a base load to reduce.
BThe slope
The kWh consumed for each additional degree-day. It reflects insulation, ventilation and the efficiency of the installation: after insulation work, it decreases.
CMonths off the line
A month that sits clearly away from the line signals a change: drift, breakdown, altered setting or unusual occupancy.

Divided by the heated floor area, annual consumption gives a ratio in kWh/m² that places the building on a scale from A++ to G. Calculated from actual consumption, this rating is indicative: it does not replace the EPB certificate, which is drawn up by a certifier based on the building’s characteristics.

Indicators

The figures to watch.

A few indicators are enough, as long as they are tracked regularly and always compared with something: the same period of the previous year, a similar building or a benchmark value.

kWh/m²

Consumption per m² per year

Compares buildings of different sizes and positions them against the benchmark values for their category (offices, schools, care homes…).

kWh/DD

Consumption per degree-day

Tracks heating performance from one period to the next, whatever the weather.

kWh

Base load

What the building consumes at night, at weekends or in summer. A rising base load points to a forgotten appliance, a schedule gone wrong or a leak.

h

Heating time per room

With room-by-room control, each room’s heating hours show where the heat goes.

€

Cost

kWh multiplied by your tariffs: savings can also be read in euros.

kg CO₂

CO₂ emissions

Each energy source has its own emission factor: the kWh saved become kilos of CO₂ avoided.

Proving savings

Savings are measured against what would otherwise have happened.

Comparing two bills proves nothing: the climate, occupancy or schedules may have changed in the meantime. The international IPMVP protocol describes the right method, and energy accounting provides the data.

  1. Baseline period: before the action, consumption is measured over a representative period.
  2. Model: a relationship is established between consumption and what makes it vary, for example degree-days (the energy signature).
  3. Adjustment: after the action, the model calculates what the building would have consumed under the actual conditions of the new period.
  4. Savings: the difference between this adjusted consumption and the measured consumption.

Savings = adjusted baseline consumption − measured consumption

With AIDHOM

Automatic readings, down to the room.

At AIDHOM, energy accounting is combined with remote management: the equipment that controls the heating also measures consumption, and ECO-MANAGER analyses it. No more manual readings or spreadsheets to keep up to date.

Read the meters

M-Bus meters are read by the ECO-CHES M-Bus master card. The ECO-IOT counts the pulses from gas, water or electricity meters, reads digital electricity meters through their P1 port and records the temperature probe readings.

Track every room

In each room, the ECO-REG records heating times: consumption can be tracked down to the room, normalised to degree-days.

Analyse

ECO-MANAGER calculates degree-days (base 16.5 °C by default, adjustable), compares them with the average of the last five years, plots the energy signature, gives the building’s rating and draws up energy balances in kWh, euros and CO₂.

Get alerted

Minimum and maximum thresholds for each meter trigger an email alert: abnormal water consumption or a drift is dealt with without waiting for the bill.

After installation, a test period of 2 to 8 weeks records the consumption of each room. These measurements are used to assess the possible savings and to set each room’s schedule with you.

Discover the software

Questions

What people often ask us.

Do existing meters need to be replaced?

Not necessarily. Many meters already have a pulse output, an M-Bus interface or, for electricity, a P1 port: they can be connected as they are. Otherwise, a sub-meter is fitted where the measurement is useful, for example on a heating circuit or on the hot water.

How often should meters be read?

Once a month is the minimum to follow the trend. To spot a drift quickly, a daily or even hourly reading is far more effective: that is the whole point of automatic readings.

How does it differ from an energy audit?

An audit is a snapshot: it analyses the building at a given moment and proposes improvements. Energy accounting is a film: it tracks consumption continuously, shows the effect of each action and spots drifts.

The two complement each other: energy accounting gives the auditor reliable data, then checks that the recommendations bear fruit.

What about the EPB certificate?

The EPB certificate assesses a building’s theoretical performance, calculated from its characteristics (insulation, installations) for standard use. Energy accounting measures actual consumption, with the building’s real occupants and schedules.

A large gap between the two is useful information in itself: it often points to a settings or usage problem.

How much can be saved?

Monitoring alone saves nothing: the savings come from the actions it triggers. But by showing drifts day by day and the effect of each setting, it makes those actions possible and helps them last.

Room-by-room control then acts directly on the areas identified: our frequently asked questions include a worked example.

Who should be in charge of it?

An energy manager, even part-time, who checks the figures every week and follows up on actions. With automatic readings and alerts, the time spent collecting data disappears: what remains is analysis and decision-making.

Want to start keeping your energy accounts?

Book an appointment: we will look at your meters and your consumption, and show you ECO-MANAGER.

Choose a date +32 (0)4 377 10 52